North Island 0800 4 BLADES
smartphone-303-726-977-823

Absolute Floor Solutions

Know what Concrete Finish you are getting!


The greatest benefit of a polished concrete floor is the cost factor.

If floors are polished correctly, it represents outstanding value for the finish and ongoing maintenance of the floor.

The problem with Polished Concrete floors is knowing if what you expect, is what you are getting!

* In the absence of an industry standard, many contractors, and suppliers of products within the industry have presented their process and products as a "standard".

This has led to multiple 'Standards' that do not offer accountability.
The lack of accountability allows polished finishes to fall short of the quality that should be achieved. In turn, this has affected the credibility of polished concrete floors internationally.

3a18d34aea8746bf5a67856aea6b84ab-454

chart1-766

How can you Measure a Polished Concrete Finish?

To address the concerns around the Lack of Credibility & Accountability, the American Concrete Sawing & Drilling Association (CSDA) developed the first Industry Standard, the ST-115.

The standard uses a Roughness Average (Ra) meter to physically measure the texture of the concrete surface microscopically with a Diamond tipped stylus and gives the data as a number that can be referenced to a table that gives the surface measured a grade.

Now, a level of finish is achieved by specifying the desired Ra range, holding the contractor to an agreed standard. This means regardless of who is doing the  polishing or the condition of the concrete surface, the same floor finish is achieved every time

Taking the Measure of Polished Concrete
  • "The CSDA believes that gloss levels shouldn't be a matter of opinion, but should be based on measurable, quantifiable standards."

    -Christopher Bennett, Husqvarna Construction Products

  • "To date, ST-115 is the only tool I know of that offers the design community quantifiable, scientific, and perhaps most importantly, repeatable results."

    -Christopher Bennett, Husqvarna Construction Products

  • "While the term "grit" is a common and even useful reference to describe gloss levels, it has not been able to precisely define the polish level on any proven, acceptable, repeatable scale."

    -Christopher Bennett, Husqvarna Construction Products

  • "Measure what is measurable, and make measurable which is not so."

    -Galileo

  • Check Out the Full Story Here.



Absolute floor-446

Providing Confidence to Acheive Beautifully Polished Concrete Surfaces - to a REAL Standard!

 
  • A concrete polishing process that achieves the only industry developed standard, the ST115 American Standard for refinement of concrete surfaces!
  • Providing both the Consumer & the Contractor confidence that the desired result is being acheived
  • Measurable, Sustainable & Repeatable results in Polished Concrete finishes

Don't just "Roll The Dice" on your polished concrete surface.

Talk to Absolute Diamond about how we can assure you that the floor you dreamed of is what is delivered.

  • Eco-Friendly additives by DecoCrete EU.
  • Durable & Low Maintainence
  • Concrete beautifully polished to an Industry Standard (CSDA ST-115)
Wet Floor-132
Slip2-928-421Ra2

Instruments for Measuring Floor Surfaces
Are you getting what you paid for? And is it compliant to NZ slippage standards?

Light meters or distinction of image (DOI) meters are tools that tell one side of the story, but they have limitations. A light meter can tell you how much light a floor reflects, but it can’t tell you why that light is being reflected.
Likewise, A DOI meter can tell you how sharply an image is reflected in the floor. But again, it can’t tell you if the floor is actually polished to spec.
These meters are not reading the refined texture of a concrete floor, but the surface of the clear-coat epoxy or topical sealer placed over a floor. A Glossy Sealer can be put over a surface in order to reach DOI numbers but still wont indicate whether the surface of the substrate itself has been refined as specified.

An Ra Meter measures the surface of a refined substrate Prior to any sealer going down. This gives evidence to the client & reassurance to the contractor that the agreed specification has been met and the seal is not used to deceive the eye.
Once a Sealer has gone onto the floor, an Ra Meter is no longer reading the substrate surface texture, but that of the Sealer.

A Slip Meter (tribometer) provides a simple method of testing a floors static Co-Effiency for compliance against slip hazards.
A slip meter whilst can be used wet or dry is often used to confirm a finished floor surface is slip resistant when it's wet.
New Zealand slip compliance value is defined as having a surface with a Co-Effient of Friction (CoF) reading greater than 0.4 or a Slip Resistant Value (SRV) of 39 or greater

ABOUT US

Absolute Diamond Blades Ltd aims to help diamond tool operators get the most out of their diamond blades...

Read more
 

WHAT’S NEW

Check out the latest Products & Tech, constantly being updated on or What's New Page...

See What's New this Month...
 

CONTACT US

North Island - 0800 4 BLADES

@absolute.diamond Fb Insta Youtube-969-647-720Fb Insta Youtube-969-262Fb Insta Youtube-969-685

Click Here for more Details